# generated by SuperSlicer 2.3.55 on 2021-03-29 at 04:47:20 UTC
[print:0.2 NORMAL]
allow_empty_layers = 0
avoid_crossing_not_first_layer = 1
avoid_crossing_perimeters = 0
avoid_crossing_perimeters_max_detour = 0
bottom_fill_pattern = monotonicgapfill
bottom_solid_layers = 4
bottom_solid_min_thickness = 0
bridge_acceleration = 0
bridge_angle = 0
bridge_flow_ratio = 95%
bridge_overlap = 100%
bridge_speed = 30
bridge_speed_internal = 100%
bridged_infill_margin = 200%
brim_ears = 0
brim_ears_detection_length = 1
brim_ears_max_angle = 125
brim_ears_pattern = concentric
brim_inside_holes = 0
brim_offset = 0
brim_width = 0
brim_width_interior = 0
clip_multipart_objects = 1
compatible_printers =
compatible_printers_condition =
complete_objects = 0
complete_objects_one_skirt = 0
complete_objects_sort = object
curve_smoothing_angle_concave = 0
curve_smoothing_angle_convex = 0
curve_smoothing_cutoff_dist = 2
curve_smoothing_precision = 0
default_acceleration = 0
dont_support_bridges = 1
draft_shield = 0
duplicate_distance = 10
enforce_full_fill_volume = 1
ensure_vertical_shell_thickness = 0
exact_last_layer_height = 0
external_infill_margin = 150%
external_perimeter_cut_corners = 0%
external_perimeter_extrusion_width = 0.45
external_perimeter_overlap = 100%
external_perimeter_speed = 50%
external_perimeters_first = 0
external_perimeters_hole = 1
external_perimeters_nothole = 1
external_perimeters_vase = 0
extra_perimeters = 0
extra_perimeters_odd_layers = 0
extra_perimeters_overhangs = 0
extruder_clearance_height = 25
extruder_clearance_radius = 45
extrusion_width = 0.45
fill_angle = 45
fill_angle_increment = 0
fill_density = 13%
fill_pattern = rectilinear
fill_smooth_distribution = 10%
fill_smooth_width = 50%
fill_top_flow_ratio = 100%
first_layer_acceleration = 0
first_layer_extrusion_width = 0.675
first_layer_flow_ratio = 100%
first_layer_height = 0.2
first_layer_infill_speed = 12.5
first_layer_size_compensation = 0
first_layer_speed = 12.5
gap_fill = 1
gap_fill_min_area = 100%
gap_fill_overlap = 100%
gap_fill_speed = 30
gcode_comments = 0
gcode_label_objects = 1
hole_size_compensation = 0
hole_size_threshold = 100
hole_to_polyhole = 0
infill_acceleration = 0
infill_anchor = 600%
infill_anchor_max = 0
infill_connection = connected
infill_connection_bottom = notconnected
infill_connection_solid = connected
infill_connection_top = connected
infill_dense = 0
infill_dense_algo = autoenlarged
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0.45
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 60
inherits =
interface_shells = 0
ironing = 0
ironing_flowrate = 15%
ironing_spacing = 0.1
ironing_speed = 15
ironing_type = top
layer_height = 0.2
max_print_speed = 120
max_volumetric_speed = 0
milling_after_z = 200%
milling_extra_size = 150%
milling_post_process = 0
milling_speed = 30
min_skirt_length = 4
min_width_top_surface = 200%
model_precision = 0.0001
no_perimeter_unsupported_algo = none
notes =
only_one_perimeter_top = 0
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = {input_filename_base}_{layer_height}mm_{filament_type[0]}_{printer_model}_{print_time}.gcode
over_bridge_flow_ratio = 120%
overhangs_reverse = 0
overhangs_reverse_threshold = 250%
overhangs_speed = 100%
overhangs_width = 80%
overhangs_width_speed = 40%
perimeter_acceleration = 0
perimeter_bonding = 0%
perimeter_extruder = 1
perimeter_extrusion_width = 0.45
perimeter_loop = 0
perimeter_loop_seam = rear
perimeter_overlap = 100%
perimeter_speed = 60
perimeters = 3
post_process =
print_extrusion_multiplier = 100%
print_retract_length = -1
print_retract_lift = -1
print_settings_id =
print_temperature = 0
raft_layers = 0
resolution = 0.0125
seam_angle_cost = 100%
seam_position = hidden
seam_travel_cost = 20%
single_extruder_multi_material_priming = 0
skirt_distance = 5
skirt_extrusion_width = 0
skirt_height = 1
skirts = 1
slice_closing_radius = 0.049
small_perimeter_max_length = 20
small_perimeter_min_length = 6%
small_perimeter_speed = 25
solid_fill_pattern = rectilineargapfill
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0.45
solid_infill_speed = 100%
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_angle = 0
support_material_auto = 1
support_material_buildplate_only = 1
support_material_contact_distance_bottom = 0.15
support_material_contact_distance_top = 0.15
support_material_contact_distance_type = filament
support_material_enforce_layers = 0
support_material_extruder = 0
support_material_extrusion_width = 95%
support_material_interface_contact_loops = 0
support_material_interface_extruder = 0
support_material_interface_layers = 2
support_material_interface_pattern = rectilinear
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear-grid
support_material_solid_first_layer = 1
support_material_spacing = 2
support_material_speed = 60
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 100%
thin_perimeters = 1
thin_perimeters_all = 0
thin_walls = 1
thin_walls_merge = 1
thin_walls_min_width = 50%
thin_walls_overlap = 50%
thin_walls_speed = 25
threads = 24
top_fill_pattern = monotonicgapfill
top_infill_extrusion_width = 0.4
top_solid_infill_speed = 50%
top_solid_layers = 5
top_solid_min_thickness = 0
travel_speed = 200
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_brim = 150%
wipe_tower_no_sparse_layers = 0
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 160
wipe_tower_y = 160
xy_inner_size_compensation = 0
xy_size_compensation = 0
 
[filament:Bestfilament PETG]
bed_temperature = 80
bridge_fan_speed = 100
chamber_temperature = 0
compatible_printers =
compatible_printers_condition =
compatible_prints =
compatible_prints_condition =
cooling = 1
disable_fan_first_layers = 3
end_filament_gcode = "; Filament-specific end gcode"
external_perimeter_fan_speed = -1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 10
filament_colour = #FF8000
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cooling_zone_pause = 0
filament_cost = 1100
filament_density = 1.27
filament_deretract_speed = 0
filament_diameter = 1.75
filament_dip_extraction_speed = 70
filament_dip_insertion_speed = 33
filament_enable_toolchange_part_fan = 0
filament_enable_toolchange_temp = 0
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_speed = 0
filament_max_volumetric_speed = 15
filament_max_wipe_tower_speed = 0
filament_melt_zone_pause = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_retract_before_travel = 2
filament_retract_before_wipe = nil
filament_retract_layer_change = nil
filament_retract_length = 2
filament_retract_lift = 0
filament_retract_lift_above = nil
filament_retract_lift_below = nil
filament_retract_restart_extra = nil
filament_retract_speed = 25
filament_settings_id = ""
filament_shrink = 100%
filament_skinnydip_distance = 31
filament_soluble = 0
filament_spool_weight = 1000
filament_toolchange_delay = 0
filament_toolchange_part_fan_speed = 50
filament_toolchange_temp = 200
filament_type = PETG
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
filament_use_fast_skinnydip = 0
filament_use_skinnydip = 0
filament_vendor = Generic
filament_wipe = 0
filament_wipe_advanced_pigment = 0.5
filament_wipe_extra_perimeter = nil
first_layer_bed_temperature = 90
first_layer_temperature = 245
full_fan_speed_layer = 0
inherits =
max_fan_speed = 98
max_speed_reduction = 50%
min_fan_speed = 0
min_print_speed = 12.5
slowdown_below_layer_time = 10
start_filament_gcode = ""
temperature = 235
top_fan_speed = -1
 
[printer:SOVOL SV01]
bed_custom_model =
bed_custom_texture =
bed_shape = 0x0,270x0,270x250,0x250
before_layer_gcode = ;BEFORE_LAYER_CHANGE\n;[layer_z]\n\n
between_objects_gcode =
color_change_gcode = M600
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_filament_profile = "Creality PLA @CREALITY"
default_print_profile = 0.20mm NORMAL @CREALITY
deretract_speed = 25
end_gcode = {if max_layer_z < max_print_height}G1 Z{z_offset+min(max_layer_z+2, max_print_height)} F600{endif} ; Move print head up\nG1 X5 Y170 F{travel_speed*60} ; present print\n{if max_layer_z < max_print_height-10}G1 Z{z_offset+min(max_layer_z+70, max_print_height-10)} F600{endif} ; Move print head further up\nM140 S0 ; turn off heatbed\nM104 S0 ; turn off temperature\nM107 ; turn off fan\nM84 X Y E ; disable motors\n\nM300 S1567 P166\nM300 S1479 P166\nM300 S1046 P166
extra_loading_move = -2
extruder_colour = #FFFF00
extruder_fan_offset = 0%
extruder_offset = 0x0
extruder_temperature_offset = 0
fan_kickstart = 0
fan_speedup_overhangs = 1
fan_speedup_time = 0
feature_gcode =
gcode_flavor = marlin
gcode_precision_e = 5
gcode_precision_xyz = 3
high_current_on_filament_swap = 0
host_type = octoprint
inherits =
layer_gcode = ;AFTER_LAYER_CHANGE\n;[layer_z]
machine_limits_usage = time_estimate_only
machine_max_acceleration_e = 5000
machine_max_acceleration_extruding = 500
machine_max_acceleration_retracting = 1000
machine_max_acceleration_travel = 1500,1250
machine_max_acceleration_x = 500
machine_max_acceleration_y = 500
machine_max_acceleration_z = 100
machine_max_feedrate_e = 60
machine_max_feedrate_x = 500
machine_max_feedrate_y = 500
machine_max_feedrate_z = 10
machine_max_jerk_e = 5
machine_max_jerk_x = 8
machine_max_jerk_y = 8
machine_max_jerk_z = 0.4
machine_min_extruding_rate = 0
machine_min_travel_rate = 0
max_layer_height = 0.32
max_print_height = 300
milling_diameter =
milling_toolchange_end_gcode =
milling_toolchange_start_gcode =
milling_z_lift =
min_layer_height = 0.04
min_length = 0.035
nozzle_diameter = 0.4
parking_pos_retraction = 92
pause_print_gcode =
print_host =
printer_model = CR10V3
printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_CREALITY\nPRINTER_MODEL_CR10V3
printer_settings_id =
printer_technology = FFF
printer_variant = 0.4
printer_vendor =
printhost_apikey =
printhost_cafile =
printhost_port =
remaining_times = 0
retract_before_travel = 1
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 1
retract_lift = 0.4
retract_lift_above = 0
retract_lift_below = 0
retract_lift_first_layer = 0
retract_lift_top = "All surfaces"
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 50
silent_mode = 0
single_extruder_multi_material = 0
start_gcode = G90 ; use absolute coordinates\nM83 ; extruder relative mode\nM140 S[first_layer_bed_temperature] ; set bed temp\n\nG28 ;Home\nG1 Z300 F150                    ;Move Z Axis up\nG1 Z10 F150                     ;Move Z Axis down\nG29 A; to turn leveling on\nG29 L1 ;Load mesh\nG29 J2 ;Four point level\n\nM190 S[first_layer_bed_temperature] ; wait for bed temp\nM104 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; set extruder temp\nM109 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; wait for extruder temp\n\n;Wannabe\nM300 S1567 P120\nM300 S0 P20\nM300 S1567 P120\nM300 S0 P20\nM300 S1567 P120\nM300 S0 P20\nM300 S1567 P120\n\nG92 E0                            ;Reset Extruder\nG1 Z2.0 F3000                     ;Move Z Axis up\nG1 X10.1 Y20 Z0.28 F5000.0        ;Move to start position\nG1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line\nG1 X10.4 Y200.0 Z0.28 F5000.0     ;Move to side a little\nG1 X10.4 Y20 Z0.28 F1500.0 E30    ;Draw the second line\nG92 E0                            ;Reset Extruder\nG1 Z2.0 F3000                     ;Move Z Axis up
template_custom_gcode =
thumbnails = 0x0,0x0
thumbnails_color = #018aff
thumbnails_custom_color = 0
thumbnails_with_bed = 1
time_estimation_compensation = 100%
tool_name = ""
toolchange_gcode =
use_firmware_retraction = 0
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 0
wipe = 1
wipe_advanced = 0
wipe_advanced_algo = linear
wipe_advanced_multiplier = 60
wipe_advanced_nozzle_melted_volume = 120
wipe_extra_perimeter = 0
z_offset = 0
z_step = 0.04